Postprocess workflow doubts between Reach base and a closer permanent station
@francesco_b wrote: Dears, This is my first post here. I am trying to post-process surveys I have done with two Emlid Reach. I am a beginner and even after reading the Emlid post-processing tutorial,...
View ArticleWanted - Used Navio2 UK
@Low wrote: Just wondering if anyone has a 2nd hand Navio2 in the UK for sale ? Posts: 1 Participants: 1 Read full topic
View ArticleAbout ESCs and Power supplies
@Andrew_L wrote: Hi, I am confused about the picture which shows connection between ESCs and Power supplies. And here is a question… Q. According to this scheme, the re and black wires on all four...
View ArticlePos accuracy problem
@2281280195 wrote: Fly these many days many times, pos data through RTKLIB processing has always been Q = 1, Q = 2, Q = 5 exist. This is one of a group of data, trouble you to help analyze. Thank you!...
View ArticleClik here to view.
The result of processing raw data is that the positioning flags are floating
@2281280195 wrote: This module has been tested many times in recent days, and the data processed are not entirely green. there are points where Q = 1, Q = 2, and Q = 5. The following is a set of data...
View ArticleRTKPOST X64 skip entered base coordinate
@topo wrote: Hello, I am testing RTKPOST x86 and x64 found below : https://files.emlid.com/RTKLIB/RTKLIB-Win-x86.zip (2.4.3 Emlid b27) https://files.emlid.com/RTKLIB/RTKLIB-Win-x64.zip (2.4.3 Emlid...
View ArticleNew to Collecting GCP
@aerialcov wrote: Hello Everyone, I am new in collecting ground control points for aerial surveys. Right now I am using a matrice 210 with pix4d capture. I am wondering the best ways to capture the...
View ArticleNeed help for Joystick control problems
@Alessio_Tusca wrote: Hello guys, i’m putting my first build together and i want to get it work (at least hover) with my xbox one controller via MAVlink. I don’t have an RC controller and the...
View ArticleClik here to view.
[Help!] About materials we need
@Andrew_L wrote: According to forum this article, we need snap knife, solder wires, and soldering station as tools. Can you explain to me for why we need these? Thank you very much. Posts: 2...
View ArticleAny plans for using the M8P chip?
@dean wrote: Just curious if the team at Emlid are looking at utilising the u-blox M8P that has RTK functionality built into the receiver, possibly removing the need for the Edison? I’m guessing such...
View ArticleCalculate azimuth and distance between rover and base
@baloodev wrote: I’m trying to calculate azimuth and distance between Rover and Base. These are my first steps in this area. I’ve bought Reach RTK kit and followed this tutorial Bluetooth output and...
View ArticleClik here to view.
HowTo: ReachView settings for PPK
@bide wrote: The purpose here is to show you the basic ReachView settings for PPK. I have provided screenshots of each tab within ReachView and annotated them in RED writing. We will not discuss...
View ArticleAbout the ReachView category
@dmitriyershov wrote: This category covers questions concerning ReachView app. Before submitting question, please check the documentation once again and make sure that you are running latest ReachView...
View ArticleClik here to view.
Apply a time offset for timestamp on Reach. Experimental
@TB_RTK wrote: This should be a familiar issue for those who run into hotshoe sync problems and trying to log accurate timestaps on Reach. How to log exact time when a photo is taken? And we are...
View ArticleDo you guys know how to set up the coding page on Rapberry Pi OS?
@Andrew_L wrote: We are going to be working on programming. And we do not know how to get to those four panels on the screen. Can you guys give me some steps to get it? Posts: 4 Participants: 2 Read...
View ArticleHow to receive Reach RTK GPS data on Raspberry Pi 3 via USB?
@marc.gonzalez wrote: Hi Emlid Community, Could anyone kindly provide information on how to set up the Reach RTK to send data via USB to a Raspberry Pi 3? I’ve seen some documentation on the...
View ArticleStep by step procedure to establish a network connection with a DUB-E100 a...
@plh wrote: Is it possible to have a step by step procedure to establish a network conneciton with a DUB-E100 a reach module? Thank you! Posts: 2 Participants: 2 Read full topic
View ArticleClik here to view.
My Base and Rover setup
@DaneGer21 wrote: Just sharing a few pics of my setup to maybe help others with ideas on where to start, or what to improve from my setups. Nothing major here, and pretty basic, DIY and cheap was my...
View ArticleAltitude accuracy reach rs
@markwatsonsafc wrote: Hi, I am just really starting with Reach RS, using one as a base station and one as a rover I seem to get excellent results for lat and long. However when I compare the altitude...
View ArticleHeight of the antenna
@Mario_Lemus wrote: Height of the antenna Good morning, I have a silly question. The height of the antenna is the height of the base or refers to the height of each measurement point. Check the...
View Article