Navio2 pi image - RT Preempt
@Mikebert4 wrote: Just a quick clarification needed from @Emlid The navio2 rpi image provided in the docs works great (I've got APM up and running and everything) - is there a link to the kernel...
View ArticleUsing Emlid in very remote areas
@ElisaFRI wrote: Hi all, I probably need to use Emlid Rover-Base in very remote areas where I will not have Wifi or GSM connection. I need to log raw data of both Rover and Base, and RTK solutions...
View ArticleNavio+ Image to Navio2 Comaptibility
@jstromsoe wrote: @ivereninov Well, finally the worst happened and I somehow accidentally powered the servo rail on my Navio+ with 16.2v instead of 5v. This resulted in a dead Navio+ AND a dead RPi2....
View Article3DR SOLO with REACH
@Mayehem wrote: Hello! Has anyone attempted to add reach on to the Solo platform yet? I am going to give it a go in the coming months, adding it as a second GPS or swapping it for the NEO-7 on board...
View ArticleCamera Triggering
@cndnflyr wrote: I've been able to trigger my sony camera with a Skysight Mono using PWM signals from a Raspberry Pi. I would like to do the same thing with the Reach, but I'm not sure if it's...
View ArticleReach/Wifi ? Also what is the most current update version?
@Eric wrote: I plan to use Reach out in the field far from a wifi source and my phone is not setup to be a hotspot. Even if it was most locations I will be going do not even have cell service. Can I...
View ArticleEmlid Reach Serial Output for Arduino Mega 2560
@98mazdaman wrote: Hello All, What format should the serial output coming from the reach be in? The solution output in the Reach app is set to serial. We have the serial connected to an Arduino Mega...
View ArticleNavio2 RSSI - How to implement
@jlrogers2 wrote: Hello all! I'm curious if anyone has had any success implementing RSSI with the Navio2. I found a couple of posts related to the Navio+, but they're not entirely clear how they...
View ArticleHow to fix APM's 1m maximum accuracy?
@matthewbrooks wrote: The issue of Mavlink/APM's use of floats instead of scaled integers (link1) has been brought up before here but never resolved. There is already a framework to fix this by using...
View ArticleAlternative ways to overcome GNSS Cycle Slips on Reach without IMU integration
@edmund89sg wrote: When I cold start Reach, it gives me very good accuracy on Kinematic mode when compared against plotted survey points in the field. However, as my work is under canopy sometimes, I...
View ArticleLED meaning
@Dmytro wrote: What does it mean LED colors and behavior ? I see blue blinking LED. What is it ? And where can I find documentation about this for Your standard installation ? Posts: 5 Participants: 3...
View ArticleCan I get the apk file?
@blackjack wrote: I need the apk file of the custom application that is been developed that is taken selfie picture of the navio+. The picture given in the video streaming subcategory in Navio+/2...
View ArticleNo.fix
@ducatienergia_ebike wrote: Hi everyone,this time I experimented with Reach 10 green bars, waited a lot, but still couldn't get fix solution.Why does this occur?Thank you in advance for any...
View ArticleBuilding a Module - Navio2
@Mikebert4 wrote: I'm writing this as a homage to http://community.emlid.com/t/building-a-module/65 and to update that guide with my findings for building a module for the new emlid rpi2 image. I...
View ArticleChanging PWM update frequency for individual channels
@ogulbrandsen wrote: From what I understand Navio2 has a dedicated chip for the PWM output signal that is capable of different PWM frequencies for each channels. Changing RC_SPEED in APM works, but it...
View Articlenavio2 connector issue
@raph38130 wrote: Dear all, navio2 connector pins are too thin, I have a lot of issues to get a reliable electrical connectivity with the pi2 (BTW, no issue with astro pi header, it is not relatated...
View ArticleNew Raspberry Pi 3 with 64-bit cores and built-in Wi-Fi and BLE
@ivereninov wrote: New Raspberry Pi 3 is about to be announced, it will bring 64-bit 1.2Ghz cores and Wi-Fi connectivity. It is surely an exciting update for Navio2 and we can’t wait to get it into...
View ArticleNavio2 - HIL mode with x-Plane 10
@playgemboy wrote: Can I simulate the plane using HIL with Navio2?If yes, how can i do that.If no, please support that. , i think we should have that feature. I going to use the ArduPlane firmware on...
View ArticleNavio2 - RPM sensor input
@playgemboy wrote: I have a RPM sensor with 3.3V pulse output. How can i connect this to Navio2? I see 2 spare IO of F4 MCU, does Navio2 have ability to accept the RPM input, or i have to use the RPI2...
View ArticleNavio2 - Hardware Connection map
@playgemboy wrote: Hi, i looking for Navio2 Connection Map like this one (which Navio docs have). docs.emlid.com Navio-ConnectionMap.jpg1000x563 148 KB Can you update this for the Navio2 Hardware...
View Article