Navio2 to Raspberry Pi2 Vehicle Information / Mavlink data
@jasonkschreiber wrote: Hi there. Excuse my ignorance, I'm still figuring this all out. I've got a Navio2 on a RPi2 board. I would like to do some onboard processing ... simply get the vehicles...
View ArticleMy next problem: RC failsafe does not work on FRSKY D4R-II
@drone_newbie wrote: Hello again, as always, i now have a problem setting up the RC failsafe. I am using Turnigy 9XR Pro with a FRSKY DJT transmiter and the popular FRSKY D4R-II receiver. I was more...
View ArticleBuilding pixhawk firmware directly and getting RTK data directly
@Sangjn wrote: Hi my name is Sangjin Pyo in South Korea. I have developed package delivery system by using drone which uses pixhawk as its controller and because accurate landing information is very...
View ArticleRTK accuracy without base station
@Torbjorn_Houge wrote: I am looking into using Reach, but I have no need for high real time accuracy. What I need is good accuracy after post processing, and if possible I would like to avoid the need...
View ArticleClik here to view.
Rtklibexplorer - new code
@Andreas_Ortner wrote: Hi! will you use the new code of rtklibexplorer? i think thats the problem why i often lose fix with best conditons. when would new reach view be released? Andreas...
View ArticleClik here to view.
Unable to locate package apm navio2
@matthewbrooks wrote: unable to locate.png864x540 10.8 KB What do I need to do to fix this? I need the latest version of APM. Posts: 1 Participants: 1 Read full topic
View ArticleGray bars in rover display
@matt.carp wrote: I have what is probably an easy question- the gray bars in the rover's status display, are these the base's signal strength for each of the satellites? If not, what does the gray bar...
View ArticleClarification on ESC connections in Hexacopter
@hank wrote: I am at the point where I am ready to connect my 6 ESC's to the Navio, but thought I would ask just to be sure. I am running a FrSky receiver with SBUS. I have this plugged into the first...
View ArticleNavio+ Pinouts?
@jet_flyer wrote: I'm hoping to get Navio+ running with the Snikerdoodle FPGA board https://www.crowdsupply.com/krtkl/snickerdoodleI was wondering if there was a pinout map for which pins use what...
View ArticleAccelerometer calibration fail
@Maxime_Zholdokov wrote: Hello guys,I've been triying to calibrate my accelerometer for days and it's not workingI tried with Mission Planner, APMPlanner and by wifi and ethernet, no results.What...
View ArticleClik here to view.
Can a 3dr Radio be connected via USB to the Navio?
@romulus wrote: Hello, how can I connect a radio to the Navio 2, other than the UART? As you see here, the most common radios have a Micro USB female plug:...
View ArticleReduce of EMF using copper wire - everywhere?
@romulus wrote: Hello, can the EMF of the wires in the drone, e.g. between Navio 2 < I2C standard Wire > Lidar or Rasberry Pi < USB Power Wire > Navio 2 or Navio 2 < UART standard Wire...
View ArticlePX4 flight stack now supports the Navio2
@Al_B wrote: The new PX4 1.4.1 release now claims to support the Navio2. Will Emlid update/add documentation for it as well? e.g.: Navio2 docs » Navio2 with PX4 autopilot » PX4 installation and...
View ArticleNAVIO2 - Mission Planner -> ArduCopter-single
@dronearmy wrote: Good afternoon friends !I wonder what output is used for the ESC , I can usually test on Compass Motor calibration and throttle operate normally through the RC . I´m use de output 5...
View ArticleArdupilot unexpectedly starts motors
@jharr167 wrote: I have a Raspberry pi 3 / Navio2 , on my windows 8 computer I have Mission Planner running. When I enter the sudo ArduCopter-quad -A udp:192.168.1.2:14550 command, the motor instantly...
View ArticleWhich rootfs to use?
@fxrdude wrote: HI everyone, I followed the instructions on the Emlid's github to build the kernel rpi-3.18.9-rt5 and I would like to know how to format the microsd card before copying files to it?...
View ArticleClik here to view.
My 4th quadcopter build!
@ogulbrandsen wrote: Hi! I thought I would share the progress of my current build. This will be my 4th quad using the NAVIO board. Any comments or ideas along the way are welcome! Posts: 4...
View Article3.3 V powering of reach
@Johannes_Eberenz wrote: Hello! We're planing to build a more robust housing + power solution arroudn the reach, for surveying.This will include a stable case with inbuilt battery. While the docs...
View ArticleBest long range radio telemetry with Navio2 - UK restrictions
@AndyM wrote: Hi there, I am looking to create a long range drone in the UK controlled using Navio 2. From what I understand there are quite a few restrictions on radio and it looks as if I will be...
View ArticleClik here to view.
No data from Navio2 after i put the GPS antenna
@thierrychiret2 wrote: Hello Emlid, Before putting the GPS antenna everything was ok, but after Mission Planner displays the following message : GPS: u-blox 0 is not maintainir And i have no more data...
View Article