Clik here to view.
ReachView v0.1.1
@efedorov wrote: Hello everyone, We have just released a new version of ReachView - v0.1.1. This update is focused on keeping Reach's internal clock up-to-date. Incorrect time settings could affect...
View ArticleHow do you power your 6s drone?
@Nathan_Belk wrote: I've been looking into different power boards, got one, and now I'm looking again after it burst into flame at first plug-in. I liked the idea of the one I got because it should...
View ArticleWhat device is the Navio similar too?
@Nathan_Belk wrote: When I'm looking for aftermarket parts, which other devices is the Navio similar to? Like if it works for the pixihawk, does it automatically work for the navio? Posts: 1...
View ArticleNavio2 RCInput to Output Example
@lewma wrote: Can someone point me to a simple example that shows how to translate RCInput readings into PWM outputs that I can pass to an ESC. All I need is to see how RCInput values are translated...
View ArticleGot a serious issue with ESC calibration please help
@blackjack wrote: We a building a quadcopter similar to those of Igor's build except for the esc we replaced Qbrain with emax 4 in 1.we are using FLYSKY i6 TX and FLYSKY ia6b receiver since it has ppm...
View ArticlePower Connector
@OzPup wrote: Hi All,I am using the emlid power module (expensive!) and find its connector (DF13) woefully inadequate. Has a cheap part been used for the plug as the connection is not positive at all....
View ArticleGPS solution to work with TOPCON Tesla
@Upland wrote: I wanted to know if EMLID would have a solution to get better GPS accuracy for a Topcon Tesla field controler? It has its own built in GPS, however the accuracy is only 1-5m. I have a...
View ArticleOnly broadcats wifi when powered by usb
@Eric wrote: updated both base and rover to latest app version and image. neither will broadcast wifi unless powered via usb. I need to be able to power via the df13 pins so 3dr radios can be...
View ArticleClik here to view.
ESC Calibration in Mission Planner - Raising throttle to high causes crash of...
@Upperfoot wrote: Hello everyone, I am having an issue where I am trying to calibrate my ESC's through APM on my new Navio2, I am doing the following. Run Arducopter to connect to APM Arducopter...
View ArticleBest antenna for a UAV using GPS, Glonass TW2405?
@lprrauen wrote: I have a Reach connected to a CORS network that gives me a Virtual Reference Station (VRS) so I'm getting good accuracy even though the Reach is in "float"mode most of the time. I've...
View ArticleClik here to view.
Navio2 PWM Output Frequency Limit
@i-copter wrote: I had a quick question after running some initial test. It looks like the Navio2 PWM output is limited at 400Hz regardless of setting the ESC frequency above 400Hz. As you can see...
View ArticleClik here to view.
Creating a SSH Tunnel for mavlink communications
@i-copter wrote: SSH Tunnel Good practice suggests that we should secure and encrypt the mavlink (APM Planner) connection from the GCS to the RPi. This can be easily accomplished without any...
View ArticleCompatibility with Raspberry 3 B+
@maroquio wrote: Hi, folks.Is Navio2 compatible with Raspberry 3 B+?[]s! Posts: 2 Participants: 2 Read full topic
View ArticleAPM Elevon mixing in manual mode
@Johannes_Zeiser wrote: Hey there, I just tried using my navio2 in my airplane, which is a flying wing with two elevons. I have enabeled elevon mixing in the remote callibration menu, and it works in...
View ArticleJust received a bill from DHL for unpaid duties
@Eric wrote: Well just received a rather unwelcome bill from DHL for import duties. Emlid should let potential buyers know that you will be billed another $30 after delivery. Rather dissppointing on...
View ArticleUsb input and output option in latest reach veiw version missing?
@Eric wrote: Both units updated to latest version and only UART is given as a serial input/output option. How do you setup for usb input? Posts: 1 Participants: 1 Read full topic
View ArticleUsing sudo dpkg -i after 'wget'ing navio2 apm does not work
@willyspinner wrote: Hi Emlid, I'm using a raspberry pi 2 with the navio 2 to make a quadcopteri tried to wget the navio2-apm.deb in the rpi directly, after downloading the image onto my sd card.After...
View ArticleClik here to view.
No INS Backend Available
@jstromsoe wrote: Gents, I was doing some troubleshooting today with my camera gimbal and starting having issues with my Navio+ ... I did a restart, and when it came up it complained about "No INS...
View ArticleT-REX 450 navio 2 compatibility
@Mirko_De_Nunzio wrote: Goodevening to everyone, I'm an hobbiest and i'm going to install on my t-rex 450 a NAVIO2 board, but reading in other forums no one talks about helicopters but only about...
View ArticleAdd to cart, View cart = currently empty
@guenter wrote: Hi,when I try to order a device by adding it to the cart, it's telling me: xxx has been added to the cart.When I 'View Cart': Your cart is currently empty.So is it a direct way to your...
View Article