Extension Connector Reach RS?
@timd1971 wrote: What is this mainly used for? Thank you! Posts: 2 Participants: 2 Read full topic
View ArticleClik here to view.
Rcio update keeps looping and
@frederico_ramos wrote: help with this i try to update the rcio and i get this errors and when i try to enable ardpilot i get the same on the pi3b+ IMG_20180613_163056.jpg3620x2715 2.8 MB Posts: 2...
View ArticleClik here to view.
Idea of software for integration with DJI phantom3
@andresc4 wrote: First of all, I’m new here, and I’m not a professional surveyor, just a hobbiest. I just learn a few days ago how to post process the data from my 2 emlid reach, using one as Rover,...
View ArticleNavio+ RPI3 B PWM strong twitches (servos)
@helios57 wrote: Hi, after several hours of trying to fix this I need some help. I am trying to build a Tank with a robot-arm. This includes at least 6 Servos and 2 ESC. If I plug the Servos in port...
View ArticleTrimble radio repeater
@deniswatson wrote: Is the Trimble HPB450 suitable as a radio repeater for the Reach RS. If so, do I need to change the antenna on the Rover, or does the existing one work? Posts: 2 Participants: 2...
View ArticleSetting up Pixhawk with a Reach GPS
@nijoe wrote: I am following the instructions for connecting a Reach GPS to a Pixhawk using the Mission Planner Ground Control Station (1.3.56). I had no problem until it came time to set specific...
View ArticleReach RS battery life?
@timd1971 wrote: Is it pretty typical for the Rover to drain battery quicker than the Base? I.e. Charged same time to 100% Base 92% Rover 78% Thank you! Posts: 3 Participants: 2 Read full topic
View ArticleHello, I try to connect UDP through my Custom GCS. But I can't
@mrknrk2004 wrote: Hello, There!! I am new about navio2. I am developing Custom Gcs. So I try to connect Udp between gcs and navio2. I could receive Hearbeat. Of course, I sent Heartbeat and...
View ArticleClik here to view.
Issue with MPU9250 Magnetometer
@JeanDrone wrote: Hello, I’m working on a drone and I am using Raspberry Pi 3 with the Navio2 board (Flashed with Stretch). I will work on ROS and not Ardupilot, and I need the LSM9DS1 and the MPU9250...
View ArticleIdea for Phantom 4 pro & Reach M+ = no GCPs
@Steven_Wallace wrote: DJI GS Pro supports a stop-and-shoot mode for capturing images. It’s limited to 99 shots per mission. What if you attached a Reach M+, antenna, and small battery to the P4P. Log...
View ArticleResults in wrong file format
@deniswatson wrote: I have processed my data and looks good on plot. However the position result is in an Open File document which I cannot open. Is there something wrong with my work flow process? I...
View ArticleClik here to view.
Sending a Custom Mavlink Message
@kvnchowx wrote: Hi, so I am trying to figure out how to send a custom Mavlink message from my Raspberry Pi (which has the Navio2 attached) to my PC. I’ve searched Google for quite a while and did not...
View ArticleCan I use Reach RS Base & Rover without internet access?
@timd1971 wrote: Let’s say I am in a remote area, no 4G, no hotspot for internet. Just the Base and Rover with LoRa. I just need to stake points based on 2 known control points. Will I still be able...
View ArticleFix to float effects on UAV
@podos wrote: Hi there! I am currently performing accuracy testing with my reach modules to eventually use them for UAV guidance. Here is my setup: Both antennas on the ground of a football field with...
View ArticleClik here to view.
ReachView v2.13.0 dev update - GLONASS AR
@efedorov wrote: Hello everyone, We’ve just pushed a new dev update - v2.13.0. This update contains huge improvements for our positioning engine, RTKLIB. Starting with this version, Reach can peform...
View ArticleAccuracy
@maritimenovelties wrote: Hi there. I have just unboxed my Emlid reach, i had no trouble setting it up but the altitude is 45 m too high. im in the uk what are the best settings for me please? Posts:...
View ArticleStrange calibration Accel-Gyro-Magne in driver MPU9250
@CiFFiRO wrote: Hello. I have a questions about calibration MPU9250. Driver had two function MPU9250::calib_acc and MPU9250::calib_mag. But this functions can’t calibrate or calibrate with very low...
View ArticleCorrections?
@timd1971 wrote: I am very new to Reach RS, but have been making a lot of headway with all of this but have still much to learn. Does anyone have any simple help and setup “dumbed down” so I can get a...
View ArticleClik here to view.
Coordinate Systems?
@timd1971 wrote: Making a lot of headway, but running into a couple snags. I have a Trimble Nomad 900G also with Microsurvey FieldGenius, Layout, SatViewer and TerraSync using with 2 Reach RS units....
View ArticleSetting up Trimble Nomad 900G with Reach RS
@timd1971 wrote: I am having trouble setting up Trimble Nomad 900G to switch from COM2 internal unit satellite receiver to using the Reach RS rover receives data to pass through to it instead?...
View Article