Problem with navio2 connection to missionplanner
@torebekzhumabek wrote: I installed missionplanner 1.3.46 to my laptop which is on windows 7. I configured NAVIO2 via ssh to run arduplane automatically and it works fine. And now I need to connect...
View ArticleSingle, Float & Fix?
@timd1971 wrote: How does ReachView know when it is "Fix"ed? I’ve seen it sit on Float for a good while, but it measures exactly after just a minute or so, but doesn’t switch to “Fix” even after 30...
View ArticleClik here to view.
Problems Connect Reach TX pin to Arduino UNO RX pin
@Knut_F wrote: Hello I want to connecting my Reach RTK to an Arduino UNO to get NMEA position feed into the Arduino. When I use SoftwareSerial the Arduino receives the messages, no problem. The Reach...
View ArticleNavio2 quad x 8 frame
@ains98 wrote: hello! whats is the right esc connection to the navio2 by default it is wrong and i crashed drone frame. Somebody can show right hardware connnection ? Posts: 3 Participants: 2 Read...
View ArticleReach RS units for sale
@Richard_Bishop wrote: I’m selling my pair of Reach RS units due to my change of requirements. I couldn’t get them to work for me, so I’m looking to sell them. I’m UK based, so please get in touch if...
View ArticleRenaming a Reach causes it to no longer appear in Reachview app
@nijoe wrote: I am trying to set up a pair of Reach units to send/receive RTK GPS information on an autonomous boat using Ardurover with a Pixhawk controller. I have the latest (Android) version of...
View ArticleHow to transmit sensor information (or camera information) to Ground Station
@kvnchowx wrote: Okay, so I asked a similar question here: Sending a Custom Mavlink Message But since that wasn’t really getting any replies, I thought that I would make my question more general. I...
View ArticleAbout drivers values scale
@CiFFiRO wrote: Hello. I have a questions about output values for drivers MPU9250 and LSM9DS1. Accelerometers values in both sensors is multipliers of g. Gyroscopes values in both sensors is dps. But...
View ArticleRTK corrections not reaching Rover via Mission Planner
@nijoe wrote: I am trying to set up RTK GPS for the autonomous boat I am building. I am using the Mission Planner (ver 1.3.56) ground control software with a Pixhawk flight controller (2.4.8). I have...
View ArticleMissing just 2 events in a whole set
@dario.finderle wrote: Hi, till now did not have any problem with the Emlid RTK. Made a larger set of images (2000+) divided in several sets (because of field configuration) and had all events stamped...
View ArticleHDOP values issue
@ibrahimomar357 wrote: While reading from the gps, HDOP value (in GGA message) sometimes stay the same meanwhile the status changes ( from fix to float or fix to float ) and the lat_accuracy &...
View ArticleVoltage Input specifications for ReachRS
@treybr3 wrote: We have a solar panel that outputs 18V when it is fully charged and we are trying to power a Reach RS unit via USB port. We have a voltage regulator so when the voltage is over 5V it...
View ArticleReachView v2.11.0 can't start without sky view / connected antenna
@tiedtke wrote: I’m facing this problem with all Reach that I worked. I instaled a Reach in a uav… everything is ok in the field When I return to the office to download the logs, Reach connects to the...
View ArticleConnection via USB?
@timd1971 wrote: I know the micro-USB port is used for charging, but can it also be used for data coming from the Reach RS to a Samsung Note 8 Smartphone USB-C connector? I guess also to a Windows...
View ArticleStill not shipping?
@hookerlighting wrote: I believe I ordered my Reach RS units back in March or April. Your website keeps pushing back the shipping dates and now it says shipping in August… Whats going on? Are these...
View ArticleGPRMC NMEA sentence missing from Serial output
@lresh wrote: Hello I have a setup for collecting georeferenced video which requires the GPRMC NMEA sentence. Currently, I have observed (through Putty) that the output sentences from the Emlid...
View ArticleHz? Simply, what is this?
@timd1971 wrote: I see this in the Base mode settings under RTCM3 messages settings and RTK settings such as 1 Hz, 5 Hz, 14 Hz etc. Is it the amount or rate of data from the satellites? Higher the...
View ArticlePost processing static
@hedges_64 wrote: Has anyone successfully post processed reach as rover (L1 only) and leica or trimble etc (L1 and L2) as base in rtklib? In the rtklib settings am i correct to choose L1 only? Was...
View ArticleIdeal settings for steady FIX and lowest latency possible?
@timd1971 wrote: Reach RS Base and Rover units. Probably mostly using LoRa. Is there any particular connection that is the fastest? I know there are lots of variables and posts scattered about in the...
View ArticleAfter changing Reach name its no longer visible to the app
@nijoe wrote: Once I change the name of my reach I can no longer see it in the Reachview app on my Android. The Reach has its hot spot turned on. If I connect my phone to the hot spot the app doesn’t...
View Article