Setting country code for Edge
@schuermannsebastian wrote: Hi, since hostapd is no longer used to create the AP in the latest firmware, how do I set the regulatory domain for Edge? I already tried to set it manually with “iw set...
View ArticleClik here to view.
Not able echoing the mavros topics
@Stefboat wrote: Hello I got the navio2 on a raspberry pi running Emlid Raspbian, ArduCopter: 3.2-rc2. I want to use the mavros-node in ros and use the information published by it’s topics. I followed...
View ArticleRTK with onboard M8N
@michael.burham wrote: Hello, BLUF: Anyone had success with RTK and onboard UBLOX M8N GPS module and can help guide? New to Ardupilot and the scene but really eager to get a project started. I dove in...
View ArticleBad Logging
@Barry_Bolton wrote: So why would I be getting “bad logging” on my Navio2 ? Posts: 1 Participants: 1 Read full topic
View ArticleGround control point integration
@Brent_W wrote: Hey guys! Mapsmadeeasy introduced ground control points! One of the simplest low cost solutions available! Pay per use. Can’t wait to try it out....
View ArticleStatic on Emlid reach rs
@Huot_Samnang wrote: Before creating a new thread please refer to Quickstart guides for Reach and Reach RS. In case you are creating a thread about an issue please specify the appropriate sub-category...
View ArticleReach RS not updating
@fergal wrote: Hi, I’m currently running ReachView version: v2.9.3-r0 It is asking me to update to v2.10.0.0 but when it goes to the update screen it is looking to connect to a wifi network (it is...
View ArticleReducing amount of NMEA messages being output
@fergal wrote: I have an issue with the amount of NMEA messages being output by the Reach unit, it is being used for monitoring vehicle movements and is reporting to AWS. The amount of messages being...
View ArticleArduino reads from base, not rover
@okrengel46 wrote: We are currently working with the Reach RTK starter kit, attempting to read both Base and Rover GPS data over serial on an Arduino Mega. We are using TinyGPSPlus, reading NMEA data...
View ArticleFrysky telemetry
@tranquility wrote: Hello all, I have a raspberry3 with navio2 running ardupilot. My Receiver is a x4r from frysky, capable of transmitting telemetry Data to my Transmitter. I’ve read a lot about...
View ArticleQuestion about JSON dataset
@Igor_Fedorov wrote: Hello, Below you can see the point coordinates. My questions: In what quantities is the RMS measured “rms”: “0.00141306193467 0.00071638819671 0.00359942737768” (i mesured...
View ArticleTopcon corrections topnet live
@Anastasios_Balian wrote: base_201804091654_rtcm3.zip (258.3 KB) Hello I also managed to connect my Emlid antenna with fc250 and magnet software My issue is that although I bough subscription for...
View ArticleReach UART for both NMEA output and Base Corrections
@diddi.m wrote: Hi, I’m currently facing problem to get emlid reach rover and base to talk via serial uart for my project. setup: Rover module talks to onboard computer via usb-uart cp2102 : 38400,...
View ArticleNRCAN PPP - ANT#/TYPE - Reach RS
@Hilux74 wrote: Hi. Just purchased a Reach RS unit and trying to test it out by using it to GPS fixed points in a vineyard that will serve as Base Locations later. I have a question about submitting...
View ArticleAnother order status post
@hookerlighting wrote: Hi, I would like to inquire about order number 15629. When I initially ordered, shipping was estimated to begin late April, now the website says early may. I see it is still...
View ArticleAny chance to get ros-/tf directly from mavros?
@Tommy_Xiong wrote: Hi guys, I am working on a project which requires me to get the transformation information between two drones. I found that mavros should be able to send UTM coords via TF but it...
View ArticleIMU calibration APM planner
@rcommissaris11 wrote: Hello I am trying to get the IMU data of my navio2 to work. Therefore I use APM planner to process the imu data. I was able to calibrate the accelerometer and the magnetometer,...
View ArticleIs it necessary to perform a post process when the base is located on a known...
@marlonfgj wrote: Hello everyone We are starting to use two ER units to raise control points (GCP) to correct an orthophoto that will be used to update the cadastre in certain populations south of...
View ArticleClik here to view.
GPS post-processing is not very well
@coldmoonbreak wrote: Hi, I did a experiment using 2 Reach RS+. One for base, and one for rover. The date (latitude and longitude) of base is very accurate after I putted it on the ground about 30...
View ArticleArdupilot Updates
@Barry_Bolton wrote: How long does it take Emlid to publish the latest Ardupilot update in their images for Navio 2 Posts: 1 Participants: 1 Read full topic
View Article