No data when echoing Mavros
@liam wrote: Hello everybody, I’m trying to use autopilot with navio2+ardupilot, I follow the Docs but when I echo mavros I don’t get any data. I saw this topic...
View ArticleNavio2 erratic behavior and communication loss
@usmanrafiq686 wrote: Hello, I am using navio2 on hexacopter, I read all instructions from emlid docs and did everything accordingly. I also setup UART to get telemetry with my TBS crossfire using...
View ArticleFixing Reach RS. It wont turn on!
@flyinmada wrote: After having our reach RS for about a week we had a mishap and it fell off of the tripod about 2’ up. It wasn’t a tremendous fall and only left a scratch on the Emlid case. Now the...
View ArticleClik here to view.
Intel Edison workaround not working?
@jose.shea wrote: New Emlid user here - I was able to follow the first few steps in the Reach RS setup documents, but my work wifi network requires a username and password to connect. So I was unable...
View ArticleNavio vs Navio2 Ardupilot for +?
@mb300sd wrote: Should I use waf configure --board=navio2 or waf configure --board=navio when building for a Navio+? It says navio2 here (...
View ArticleReach WiFi Connection Timeout
@robj wrote: We’re using a Reach on a quadcopter, with an LTE modem/router for all our comms. The problem I’m having is that the Reach boots up more quickly than the modem/wireless AP and goes into...
View ArticleClik here to view.
Poor PPK results - But why?
@RTK_RTJ wrote: I took my 2 Reach RS out for another accuracy test yesterday. I followed a protocol which has given me great results up to this points. The simple set up entails: Set GCPs Set up base...
View ArticleClik here to view.
PPS Output - Reach Modules & Reach RS
@antimattercrusader wrote: Hello! I am wondering if there is a PPS out on Reach modules and/or Reach RS units? I know as of '16 there was not, then somehow in my mind I believed the Reach module did...
View ArticleClik here to view.
ReachView v2.11.0 - Our second stable release
@efedorov wrote: Hello everybody, As you might know, we’ve been quite busy working on the new Reach M+ and Reach RS+, which are to replace the old models. If you want to take a closer look, our new...
View ArticleNavio2 + RPi3 stack: unable to calibrate ESCs
@jim20 wrote: Hey everyone, I am new in the world of drones, and I am trying to create one using RPi3 + Navio2 as the flight controller, Mission Planner as my GCS, 3DR radio telemetry (M-Robotics SiK...
View ArticleReach RS offset
@hookerlighting wrote: Hi everyone, I have been digging through the documentation and cannot find an answer to a very simple nooby question… How exactly is one supposed to measure the offset between a...
View ArticleClik here to view.
Edge do not disarm after RTL
@mlebret wrote: Hello, Here are two logs with Edge (Firmware 1.4, Arducopter 3.5.3) https://www.dropbox.com/s/50xzz9w7zcgso8e/log_31_2018-4-11-14-50-56.bin?dl=0...
View ArticleReach module - EXIF log/triggering
@RTK_RTJ wrote: I got my hands on a Reach module that I want to strap onto a drone! Combined with my Reach RS, I will do PPK and apply those coordinates to the images and eliminate the need for GCPs....
View ArticleReinstall ReachView version 2.10.0 after upgrading to 2.11.0
@Knut_F wrote: I’m installing Ontrac3 autosteer on my tractor. It was not fully tested with ReachView version 2.10.0, but I think it worked with version 2.10.0. After upgrading to ReachView version...
View ArticleClik here to view.
Reach RS & Bluetooth Connection to Android
@RBN wrote: Hello. New forum user, but I’ve been researching the forums for a week now, and cannot seem to figure out the issue I am seeing. I am in Wisconsin, and am connecting my Reach RS rover to...
View ArticleEdge outdoor hover example?
@speedfreak_2k wrote: Hope this is the right place to ask… Does anyone have a video of the edge in outdoor hover mode? Have only seen edge videos from Emlid, but not any users. Was thinking of getting...
View ArticleClik here to view.
W10 Ubuntu Linux and Ardupilot dev
@mlebret wrote: Hello, I discovered recently Windows 10’s Bash Shell. https://www.howtogeek.com/249966/how-to-install-and-use-the-linux-bash-shell-on-windows-10/ I did the install on my W10 machine...
View ArticleExtending Lora range
@deniswatson wrote: Before creating a new thread please refer to Quickstart guides for Reach and Reach RS. In case you are creating a thread about an issue please specify the appropriate sub-category...
View ArticleClik here to view.
How to create BM
@Huot_Samnang wrote: BMcreate.jpg716x960 163 KB Please guide me how to create BM by Static mode using Emlid Reach RS Thank Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Quick Question : Is the a6000 with hotshoe feedback and ppk setup enough for...
@Nihal_M wrote: Hi, I’ve been mapping with the sony a5100 and tried to correct he Geotags from mission planner via a custom script. Needless to say, that failed. So I was looking at other solutions...
View Article