Quantcast
Channel: Emlid Community Forum - Latest topics
Browsing all 12769 articles
Browse latest View live
↧

Image may be NSFW.
Clik here to view.

ReacView configpage error + no bluetooth pairing

@Johannes_Eberenz wrote: Hi,now I also encounter with my other reach. I succefully felasshed firmaware v1.2 and reachview is v0.3.1. I cannot pair with bluetooth devices (Failed to...

View Article


Does Navio2 have to use an experimental ArduPilot version?

@Nathan_Belk wrote: I'm on the ardupilot forums working on a few issues there. I submitted my logs and this was the reply: This is development version and not ready for prime time. I would switch back...

View Article


Image may be NSFW.
Clik here to view.

Raspberry Pi 3 support for Navio is here!

@staroselskiy wrote: Originally published at: http://www.emlid.com/raspberry-pi-3-support-for-navio-is-here-2/ For the last weeks we’ve been working relentlessly on the new revision of our special...

View Article

After power cycle base lost config data

@guenter wrote: Hi,after a power OFF/ON, the base changes its config:ReachView v.0.3.1 Output Path for corrections from 'serial' USB 57600baud (my setting) to --> tcpsvr port 9000 ?? and at the...

View Article

Image may be NSFW.
Clik here to view.

My first Navio 2 build and I need a suggested parts list to purchase

@ADSB2016 wrote: I'm a Precision Agriculture company owner that builds UAV's for scouting crops. I have built many quads and I've been watching out for something new and exciting to revolutionize the...

View Article


Reach setup failed to find my iPad hotspot on setup

@Rabun wrote: I turned on the Personal Hotspot on my iPad Air. Powered up the Reach. After a minute or so the Reach appeared in the available Wifi networks In Browser typed http://192.168.42.1.5000...

View Article

RasPi 3 Wifi broadcast

@Garrett_Taves wrote: So, I've seen the half completed guide @CodeChief posted to get the Pi to broadcast its own wifi network (and distribute the UDP packets to the entire network) , but it's not...

View Article

Autonomous drone

@leonardo.cecchin wrote: Hi everyoneI'm developing a project of a quadcopter that has to autonomously find a radio beacon in a radius of 50/100m, I've the beacon and the receiver, the receiver is now...

View Article


Getting positioning out, without ReachView APP

@rep wrote: Hi colleagues, I would like to know if will be possible to get the position from the Reach device, without opening the web APP. I suppose that I will have to configure a solution output as...

View Article


Image may be NSFW.
Clik here to view.

Input From Base and output to ATMEGA both on Serial

@MakerMark wrote: Hy Guys, i'm trying to configure a couple of reach. The base station send via UART @ 57600 with a 3dr telemetry to the rover station, the rover station receive via UART the base...

View Article

Beginner Questions

@TheFunk35 wrote: I have a few questions regarding software and ESC configuration, in addition to some advice for leads. I figured I'd ask here first because I already have an account here and y'all...

View Article

Image may be NSFW.
Clik here to view.

Problems getting fix with post processing

@Jonathan_Bailey wrote: I am attempting to use the Reach to mark ground control points for drone surveying. However I am having trouble getting a fix - seems like I can only get float. I'm running the...

View Article

Configure ArduPilot for 57600 baud UART?

@Klejs wrote: Hi All I have a set of hkpilot telemetry which run at 57600 baud. How do I launch ArduPilot with full telemetry at this baud rate? /Yhanks Posts: 2 Participants: 2 Read full topic

View Article


Reach unit won't join WIFI network

@matt1973 wrote: Both of my Reach units have been working fine up until now, with credentials set up for both my home WIFI network and my mobile phone hotspot, for when I am in the field. As of last...

View Article

Pitching inverted on Mission Planner

@Guiboy wrote: HelloI get some strange behavior from my compass or accelerometer When I pitch my quad on the left, Mission planner OSD makes as if it would be pitching on right. Same behavior in the...

View Article


Image may be NSFW.
Clik here to view.

DIY - Reach and antenna box. Poor mans solution

@TB_RTK wrote: How to build your own cheap and portable survey basestation and roverpole (rover comming soon) Requirements:1. 10-20cm of your or anybody elses favourite broomstick and chop in to...

View Article

Reach Antenna & Ground Plane Choice

@Jonathan_Bailey wrote: I have a question regarding antennas - Luke W recommends the TW2410. I have tried using a TW3040 and a TW3400, based on some reading I did, and can unequivocally say that the...

View Article


Odroid C2 and Navio2

@theleon wrote: So there has been a lot of problems with getting the Navio+ and Odroid C1 to work together (https://community.emlid.com/t/odroid-c1-and-navio/117) but what about the Navio2 and Odroid...

View Article

ArduPlane -C outputs bad file describer and garbled hex chars

@Klejs wrote: Hi All When I run ArduPlane in a shell with -C /dev/ttyAMA0it outputs random hex chars and beeps and periodically "pread: Bad file descriptor" Does anyone know why this happens?...

View Article

Image may be NSFW.
Clik here to view.

Base started but no activity

@Antoine_Pouliot wrote: Hey all,I just purchased the kit and am trying to get it to work outside. I'd like to eventually use it for agricultural vehicle guidance on my farm. So I follow the quick...

View Article
Browsing all 12769 articles
Browse latest View live