Using the Edison web server on the Reach module
@matt.carp wrote: I am using the Reach module with the latest firmware (2.?) image and ReachView app. I was wondering if the Reach module is using the default Linux distribution and the built-in...
View ArticleReach RS for GCP - why are two needed?
@arun.cappi wrote: HiI want to purchase a Reach RS for establishing a few ground control points for Drone surveying, maybe 5 points at the most. I have been told that I need 2 Reach RS units for this,...
View ArticleThe suitable OS for the Drones
@B.rayane wrote: Hey everyone, Can anyone of you tell me what OS is most suitable for flying a drone Posts: 12 Participants: 4 Read full topic
View ArticleGeosetter
@dicky wrote: @igorvereninov @TB_RTK @bide Hi, anyone know, how to use geosetter? My camera set to local time, then post process the flight track set to UTC. I need step by step how to use it. I have...
View ArticleClik here to view.
Reach + 3G/LTE dongle problem
@pwiacek wrote: Hi, I am trying to connect 3G dongle (Huawei E173u-2) to my REACH however I have some problem.I supply power through LiPo 10000mAh battery -> Pixhawk -> Reach everything work...
View ArticleClik here to view.
Problem with Navio2 Example compilation
@reddylopes wrote: Hello, folks! I have installed APM Navio and downloaded the examples from the repository, but when I try to compile them, I see the following error: compile error.png720x136 25.8 KB...
View Article16.04 Ubuntu flashing?
@kiwikid wrote: I recently updated to Ubuntu 16.04 and I can't seem to flash anymore - the GUI doesn't install because it says it only supports up to 15.04, and the CLI doesn't work as when I run...
View ArticleClik here to view.
Quick test of height value. Reach RS
@TB_RTK wrote: Yet another highly scientific and thorough test from me. I thought i do a quick height test, to see what we are dealing with. Used 2 x RS, one as base with average base coordinates...
View ArticleClik here to view.
Cannot cross-compile APM on ubuntu 14.04 64 bit
@wangxiaoliang1992 wrote: I just started to build APM from source code. I Just followed the following steps: sudo git clone --depth 1 https://github.com/raspberrypi/tools.git /opt/tools export...
View ArticleClik here to view.
Servo example
@jhjh54 wrote: Hello, I have some problem at servo example. my device is Raspberry pi 3 on Navio2 I was test the servo example. and I changed the channel(PWM_OUTPUT) , but both motors work together....
View ArticleClik here to view.
SIK Radio Connection Problems
@Jimmy_Hill wrote: My motors have finally turned up, but before I connected them I've been trying to get the SiK radios connected I have solid green lights on both radios but still not able to connect...
View ArticleConnecting Receiver to Navio2
@curtzerr26 wrote: This might be a dumb question, but we're new to the drone world. We have two radios at our disposal, the Spektrum DXe w/ AR610 receiver and a Hitec Aurora 9 w/ Hitec Optima 7...
View ArticleRCIO fails to load
@Tan wrote: Hi! I am using a custom kernel (I need OP-TEE and RT patches on a Raspberry Pi 3 model B). Kernel version is 4.6.3 I am trying to use the Navio2 board and have managed to get most of the...
View ArticlePower NAVIO2/Pi form ESC linear BEC
@yconst wrote: Hi all, I'm building a ground vehicle, I am thinking of powering the NAVIO2 from the Servo rail, using the 5v output of the car's ESC. The esc is a Hobbyking one, and supposedly has a...
View ArticleReach module (Edison) low power mode
@matt.carp wrote: I wonder if the Reach team can comment if any type of power management is used on the Reach (Edison) module? Specifically, I'm wondering if the Edison module can be put into a low...
View ArticlePre Arm RC not calibrated
@Jimmy_Hill wrote: Hi ( (Sorry its me again) Right i have the radios connected and mission planner connected. Batteries charged Mission Planner keeps repeating i need to calibrate my drone but i dont...
View ArticleArtical about new version setting up of reach on github
@zhangkaibest wrote: dear guys , i read an artical about new version setting up of reach on github , just last week , but i cant find it anywhere , do you guys know about it ? Posts: 3 Participants: 2...
View ArticleCommunicating with onboard Ublox using U-Center SBAS DGPS
@Jim_Mitchell wrote: I have been exploring using the WAAS corrections for differential GPS on my EVK-M8T and wanted to implement it on the Reach receiver I just purchased. I tried enabling the SBAS...
View ArticleClik here to view.
Tw3740, should it use aluminum plate?
@dicky wrote: For this tw3740, should I use aluminum plate? Or not?Thank you IMG-20170313-WA0018.jpg648x1152 57 KB Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
How to make the GNSS update rate 10HZ
@zhangkaibest wrote: dear guys , thanks for your help ~ can you tell me how to make the GNSS update rate 10HZ, cause i tried so many times , and dont have a clue .here is the screenshot 2017-03-21...
View Article