Reach (base) own AP can't turn on
@dicky wrote: Yesterday I measure some land parcel. My base and rover were connected to my smartphone. After finished setup base, I try to turned on base AP. Then my smartphone connection to the base...
View ArticleNavio Beta 3 Country Code In wpa_supplicant
@coby wrote: I see at some point the country code was added to top of wpa_supplicant country=GB ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev update_config=1 I am guessing this was in...
View ArticleBase station permanent mounting questions
@matt.carp wrote: I'm planning on a permanent installation of my base station. I have a couple considerations, but there could be others that I'm overlooking. I'd be interested in others' experiences...
View ArticleCant findReach on WiFi
@Barry_McCreadie wrote: HI, i went through the setup process with my Reach GNSS module, as per the instructions. i even downloaded the new drivers for the USB port (of which no mention is made in the...
View ArticleWhat's the advantage of navio2
@zhanghaijason wrote: I have a question about navio what's its advantages compared with other autopilot. It needs to work with raspi while for other autopilots, just one board is OK. And raspberry pi...
View ArticleTW 2405 Embedded GPS /GLONASS Antenna?
@Eric wrote: Anyone using the TW2405 Embedded Antenna? Looking for feedback/options for use on a custom designed vehicle mount. Posts: 1 Participants: 1 Read full topic
View ArticleAge of differential
@dicky wrote: Today I observe using ntrip metode. The connection is good. But why age of differential is always increase Start in 1 then increase until 30s. Then I move the rover, lower again, then...
View ArticlePower Supply ..is 1A enough?
@Eric wrote: Is 1A enough to run Reach and 3dr radio? Toying with the idea of using a PowerBoost from Adafruit . Posts: 1 Participants: 1 Read full topic
View ArticleCan Reach's server be configured to output UBlox rather than RTCM3 formatted...
@rrr6399 wrote: I'd like to run some real time tests using the original UBlox messages between the base and the rover rather than RTCM3 to see if this improves the processing robustness. I see that...
View ArticleGstreamer on Android
@juan128carlos wrote: Hi guys!I have had some problems trying to run Gstreamer on Android, I don´t know how can I run it?Can you help me?How can I run it on Android(I'm using the APK that's showed on...
View ArticleClik here to view.
Max # of AR Iter
@dicky wrote: What is the function of Max # of AR Iter, and why I couldn't configure it? Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Problems getting a good position on latest beta
@chha wrote: Hi all I'm completely new to this, so apologies in advance if I've overlooked something basic. I've been testing a couple of Reach units for the past few days in several different...
View ArticleGeotagging Solution For drones using Reach
@Venkatakrishnan wrote: Hi guys ,Im new to Reach and i have not yet got my hands on a Reach GNSS. I was thinking is it possible for the Reach GNSS to communicate with the camera that will be used in...
View ArticleError message while flying with a 3DR external compass
@Nacho_Carnicero wrote: Hi, I have had the following message printed today while I was flying a copter with APM 3.4.3 with a Raspberry3/navio2 config and with a 3DR external magnetometer (only...
View ArticleNavio2 / Mikrokopter BL-Ctrl V2 ESC Compatibility
@robwaat wrote: Hi, I'm trying to upgrade an old Mikrokopter Okto XL to Navio2+RPi3/Ardupilot as part of a masters project surrounding autonomous drones and was looking for some help interfacing the...
View ArticleControl landing speed at desired speed
@zhanghaijason wrote: Hello,I plan to control the quad landing speed. The desired speed is computed from pi. For ardupilot, where should I make changes so that the navio2 can execute the desired...
View ArticleClik here to view.
Precision Autopilot for Snow Grooming Equipment
@Eric wrote: Been working on this for a year now getting real close to a fully working solution and not a conglomeration of various modules, boards, wires and mass of code that live on a test rover or...
View ArticleWhere do i download the os for navio+?
@emil2 wrote: I've read the docs and everything, it would be great if some would just link it Posts: 1 Participants: 1 Read full topic
View ArticleRTKLIB CUI .exe with Time Stamp output
@cczeets wrote: Hi @efedorov @igorvereninov, Do you have a RNX2RTKP.exe file that includes creating the Time Stamp position file?We are setting up a CUI to automatically post-process our data....
View ArticleAerial photo
@dicky wrote: Hi, next week maybe I would like to do aerial photo use phantom (my office first aerial photo project). My plan is taking photos with default phantom camera and trying use reach...
View Article