Clik here to view.
How to get MPU, LSM, and GPS Readings in pi3
@wajirahapuhinna wrote: I have connected my Navio 2 with pi3 and tried to access MPU, LSM and GPS sensors. then it says sensor not enabled, but when using pi2 it is working properly. the commands I...
View ArticleBluetooth Output
@hedges_64 wrote: Hey all, Please help! I am trying to output my reach position via bluetooth to my s5 samsung galaxy. I have followed the docs instructions. Reach discovers my device and sends...
View ArticleAdvice on radio for Reach kit in Europe
@alobo wrote: In order to use the cm precision in real time in the field with no internet coverage, we would liketo link Emlid Reach base and rover using a radio. Any advice on which option would be...
View ArticleClik here to view.
I have some problem RCINPUT
@jhjh54 wrote: i have problem ...i use WFLY WFR04S it support PPM OUTPUT ,but.. RCInput is 0 how can i fix this problem..? IMG_0576.JPG3024x4032 1.94 MB 스크린샷 2016-07-26 오후 4.50.01.png1128x232 14.4 KB...
View ArticleClik here to view.
ADC readings problem
@fadilrosli wrote: I'm having the same problem. I have tested with this http://www.goodluckbuy.com/index.php?target=products&product_id=110004 Pixhawk power module and standard 60A APM power...
View ArticleWhat is the best instrument to control a autonumous boat
@Samuel_Fernandes wrote: Hello, I'm a beginner in control unmanned vehicles. I want know what is the best GPS to control an autonomous boat to sampler water in a dam, the NAVIO2 or REACH? Posts: 6...
View ArticleHow to control the Navio 2 over the Internet, when UDP sends local?
@romulus wrote: Hello, I have attached the Rasberry Pi 3 / Navio 2 to a 4G Dongle and set it up so it is connected to the internet. Is it possible therefore, when the Ground Station is connected to...
View ArticleDynamic Platform Models
@matt1973 wrote: There has been a bit of discussion on the dynamic platform model that is configured by default in the Reach units over on the RTKLibExplorer blog. It seems that the UBlox chip within...
View Article[SOLVED] Reach not connecting to wifi at boot
@Thierry_Pouplier wrote: My router and the reach are powered at the same time. Reach fail to see the wifi network when it get up. Solution:In /usr/bin/reach-setup add "wpa_cli scan" before looking for...
View ArticleStand alone Reach - RFD900 Config
@Brian_Christal wrote: Hi, I'm trying to set my Reach up without going through the Pixhawk. I can't figure out how to configure it for use with RFD900 radios. I just want to send my Reach for a ride...
View ArticleUsing zigbee for DGPS communication
@1118 wrote: We use zigbee kind of probee(zu-10) for DGPS communication.So, we set input is serial and output is serial(probee) in strsvr of rtklib for base station.And we set in rtknavi, rover is...
View ArticleReach - can't connect to ReachView app (firmware 1.2)
@matt.carp wrote: I just received my Reach modules few days ago, but I'm having a problem connecting to the module from my web browser. Initial WiFi setup appeared to work. I was able to successfully...
View ArticleRaspbian update
@drone_newbie wrote: Hello, i see in the docs that for the raspbian installation you provided an updated image some days ago emlid-raspbian-20160718.img However, I am using raspbian image...
View ArticleDifferent Settings hz on base and rover!
@Andreas_Ortner wrote: does it have an effect when i use gps1hz on base and gps10hz on rover? (i would reduce data rate). Andreas Posts: 4 Participants: 2 Read full topic
View ArticleTesting the Sensors with Python / C++ as indication for MP
@romulus wrote: Hello, I am looking to test the sensors independently before running things with Mission Planner etc. When testing the AHRS script / 3Dimu.py from...
View ArticleClik here to view.
Antenna Tracker on Navio2
@ivereninov wrote: A great post by Randy about an unsual use of Navio2 http://diydrones.com/profiles/blogs/antennatracker-v1-0-on-navio2-with-bebop2 Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Last week fix quickly, but now
@dicky wrote: Hi reach masters,I'm confused with my reach, last week on Friday I've got fix quickly, under a minute. But now I can't get it yet, I don't change the setting. Any body can help me?...
View ArticleRFD 900 radios
@jmcarthur wrote: Big shout out to Larry and Bide for help getting my radios hooked up to reach modules. I would like to point out to the Emlid team that the doc's for the RFD 900 radio's shows a...
View ArticleExternal Compass Integration with Reach & Pixhawk
@Aerobat wrote: Hi! I'm planning out my next Pixhawk build utilizing REACH and I couldn't find any documentation regarding an external compass. The GNSS unit I've used previously has an external...
View ArticleOpenCV + Navio2
@Amila wrote: Guys, Is it possible to install opencv in emlid-navio os??? if it is possible should I need to perform sudo-apt-get-update?? I'm trying to do depth image extraction using stereo cameras...
View Article